Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Top 10 typical forklift crashes ， forklift procedure must focus on these matters ！.

Blog Article

Do not undervalue the forklift at the workplace. If the procedure is bad, there will certainly be major crashes in minutes, and there are many crashes entailing forklifts.

Situation 1: The forklift freight blocked the vehicle driver's view, and the person ahead can not be located, causing a moving accident.
Case 2: In order to maintain the equilibrium of the forklift when lifting heavy products, the staff members used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the allowable width of the path and hangs on the roadside shelf, which almost causes an mishap.
Instance 4: Forklift is speeding and rolls over during a turn.
Instance 5: The forklift driver did not observe the pedestrian, and the pedestrian did not observe the forklift.
Instance 6: The forklift lifts the personnel illegally, the forklift vehicle driver does not put on the safety belt, the forklift lifter falls and the chauffeur is crushed when the forklift rolls over.
Situation 7: The forklift motorist did not put on a seat belt and fell from the car when it rolled over and was squashed.
Forklift procedure must focus on these issues ：.

Begin.
1. Before starting, observe the surroundings, and after validating that there are no barriers that impede the safety of driving, beep the horn initially and afterwards begin.
2. For cars with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be risk-free before starting.
3. When the forklift starts with a load, the chauffeur should first confirm that the tons is secure and reliable.
4. The start must be slow-moving and steady.

Driving.
1. When driving, the height between the bottom end of the fork and the ground should be maintained 300mm-400mm, and the mast should be tilted in reverse. .
2. Do not raise the fork too high when driving. When going into and leaving the task site or while driving, be careful that there will certainly be no barriers overhead. When the lots is traveling, the fork should not be raised too expensive, which will influence the stability of the forklift. .
3. After unloading, the fork must be reduced to the regular driving setting prior to driving. .
4. When turning, if there are pedestrians or vehicles close by, the driving signal must be released initially. High-speed sharp turns are prohibited. High-speed sharp turns will create the car to shed lateral security and tip over. .
5. When the forklift is downhill, it is strictly forbidden to shut off the fire and slide, and it is prohibited to brake instantly while driving with loads unless there are special circumstances.
6. When the forklift is running, it should follow the traffic rules in the factory and need to maintain a specific safety and security range from the car in front. .
7. When the forklift is running, the tons needs to remain in the most affordable position that does not prevent the driving, and the gantry ought to be effectively tilted back. The load shall not be raised except when stacking or packing. .
8. The elevation of the load have to not block the chauffeur's sight. In special conditions, when the thing influences the forward vision, drive at a reduced rate when turning around.
9. It is forbidden to turn on the ramp, neither to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it should drive securely at a low rate when entering the production workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a stabilizing role. .
12. If issues are found, they will certainly be fixed and reported in a prompt fashion, and they will certainly never operate with ailments or conceal them.

loading and unloading.
1. When fork-loading products, the distance in between the two forks ought to be adjusted as needed to make the load of the two forks balanced and not manipulated, and one side of the product must be against the shelf. .
2. It is prohibited to work with a single fork or make use of a fork top or draw. In special conditions, security warning signs have to be set up to remind bordering pedestrians. .
3. In the process of packing and discharging items, the forklift should be stopped with the brake. .
4. The speed of the car need to be slow and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the lots, and it ought to be noted that the fork pointer should not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the tons does not glide in reverse. The mast can be slanted ahead a little when the load is reduced to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so regarding prevent the collapse of the goods and injure people. .
8. Overwhelming is banned, and it is prohibited to use forks to lift workers to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to Stand-on Electric Pallet Stacker use forks to pick, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake handle to dead or dispirit the parking brake button.
3. The engine is turned off and the power is removed. (Except for unique circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 minute).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look ought to be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage ought to also be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine prior to leaving the cars and truck;.
2. When you come across someone before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go Electric Forklift Truck for Warehouse beyond 5 km/h;.
4. When driving, the low point of the cargo must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow-moving and uniform, and no activating the incline is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed to raise the goods for cross country driving.
3. It is not allowed to get the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not permitted to make use of braking force to expatriation round or easy-to-roll items.
7. It is not permitted to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844